Garmin
Reactor™ 40 Kicker Autopilot With GHC™ 50 and Stainless Steel Tilt Tube
£2,929.99
/
Tax included.
Shipping calculated at checkout.
010-02794-10
Reactor 40 Kicker autopilot for small kicker and trolling outboards, supplied with the GHC 50 touchscreen instrument and the stainless steel tilt tube the steering actuator requires.
✓
Collection or delivery in 1-2 weeks
Pickup available at Mercury Yacht Harbour
Usually ready in 2-4 days
Description
The Garmin Reactor 40 Kicker autopilot with GHC 50 and stainless steel tilt tube brings GPS-stabilised steering to boats powered by a small kicker or trolling outboard. The Reactor 40 CCU is a solid-state course computer that senses heading, attitude and rate of turn to hold a course or follow a route accurately. The system steers the outboard with a steering actuator that fits into the motor tilt tube and controls speed with a throttle actuator, so the autopilot can hold a heading hands-free. This pack includes the stainless steel tilt tube the actuator must run in, which is needed on motors whose original tube is not stainless. Control is through the supplied GHC 50, a 5 in colour touchscreen instrument with NMEA 2000, Wi-Fi and ANT+ connectivity. Dockside and Sea Trial wizards tune the system to your boat.
PRODUCT DETAILS
- GPS-stabilised Reactor 40 autopilot for kicker and trolling outboards
- Includes the stainless steel tilt tube required by the steering actuator
- Throttle actuator controls the motor speed for hands-off course holding
- GHC 50 instrument with a 5 in colour touchscreen supplied for helm control
- Solid-state CCU heading sensor with built-in attitude and rate-of-turn
- NMEA 2000, Wi-Fi and ANT+ connectivity with wireless remote support
- Reactor 40 CCU (course computer unit)
- Electronic control unit (ECU)
- Steering actuator with motor brackets and linkage hardware
- Stainless steel tilt tube
- Throttle actuator
- GHC 50 autopilot instrument
- Audible alarm
- NMEA 2000 T-connectors, drop cables, power cable and terminators
- Mounting hardware and installation instructions
No exploded diagram available for this product.
No compatible transducers listed for this product.
No spares or accessories listed for this product.
No compatible products found.
Autopilot
| Autopilot type | GPS-stabilised marine autopilot (Reactor 40 CCU course computer) |
| Drive type | Kicker; steers a small kicker or trolling outboard with a steering actuator and throttle actuator |
| Helm control | GHC 50 autopilot instrument (included) |
Drive
| Tilt tube supplied | Stainless steel tilt tube included in this pack |
| Control unit | Electronic control unit (ECU), included |
| ECU dimensions (W x H x D) | 175 x 142 x 64.5 mm (6.9 x 5.6 x 2.5 in.) |
| ECU weight | 680 g (24 oz.) |
| Steering actuator | 415 x 90 x 63 mm (16.3 x 3.5 x 2.5 in.), 1 kg (2.16 lb.); mounts in the motor tilt tube |
| Tilt tube requirement | Steering actuator must be installed in a stainless steel tilt tube |
| Throttle actuator | Throttle actuator (included) controls motor speed; mounts inside the motor housing |
Sensor
| Heading sensor (CCU) | Internal solid-state attitude and rate-of-turn sensor; primary heading source |
| CCU dimensions (L x W x H) | 170 x 90 x 50 mm (6.7 x 3.5 x 2 in.) |
| CCU weight | 575 g (20 oz.) |
| CCU water rating | IEC 60529 IPX7 |
| CCU cable length | 5 m (16 ft.) |
| Compass-safe mounting | Requires handheld-compass interference test; keep 60 cm (2 ft) from iron, magnets and high-current wiring |
Controller
| Display | GHC 50: 5 in (12.7 cm) sunlight-readable colour touchscreen, 800 x 480 WVGA |
| Connectivity | NMEA 2000, Wi-Fi and ANT+ (wireless remote support) |
Connectivity
| Network | NMEA 2000 |
| NMEA 2000 LEN | 4 (200 mA) |
| NMEA 2000 input voltage | 9 to 16 Vdc |
Electrical
| ECU supply voltage | 12 to 24 Vdc (ECU input 11.5 to 30 Vdc) |
| ECU fuse | 40 A, blade-type |
General
| Compatible motor | Small kicker / trolling outboards (for example Honda, Mercury, Yamaha with the correct bracket) |
No videos available for this product.
What type of motor is this autopilot for?
It is designed to steer a small kicker or trolling outboard. A steering actuator fits in the motor tilt tube and a throttle actuator controls the motor speed.
What is the GHC 50?
The GHC 50 is Garmin marine autopilot instrument, with a 5 in sunlight-readable colour touchscreen and NMEA 2000, Wi-Fi and ANT+ connectivity for wired and wireless control.
What power supply is required?
The ECU connects to a 12 to 24 Vdc supply through the supplied 40 A fuse, and the NMEA 2000 network is powered from a 9 to 16 Vdc source.
Is the stainless steel tilt tube included?
Yes. This pack includes the stainless steel tilt tube the steering actuator must run in, which is needed on motors whose original tilt tube is not stainless.
